设为主页  加入收藏
 
·I2S数字功放IC/内置DSP音频算法功放芯片  ·马达驱动IC  ·2.1声道单芯片D类功放IC  ·内置DC/DC升压模块的D类功放IC  ·锂电充电管理IC/快充IC  ·无线遥控方案
当前位置:首页->技术分享
TAS2770 20W数字输入D类音频放大器解决方案
文章来源:永阜康科技 更新时间:2018/7/12 15:41:00
在线咨询:
给我发消息
小鄢 2850985542
给我发消息
姚红霞 3003214837
给我发消息
张顺平 3003262363
13713728695
 
TI公司的TAS2770是具有扬声器I/V检测的数字输入单声道20W输入D类音频放大器,在12.6V电压时能向4-Ω负载提供15.4W峰值功率,连续功率11.6W,THD+N小于0.03%,VBAT电压为4.5 V到16 V,主要用在平板电脑,蓝牙扬声器,家庭自动化和智能扬声器/物联网(IoT).本文介绍了TAS2770主要特性,框图,应用电路以及PC立体声音频参考设计TIDA-01572主要特性,框图,电路图,材料清单和PCB设计图.
The TAS2770 is a mono, digital input Class-D audioamp
lifier optimized for efficiently driving high peakpower into small loudspeakers. The Class-D amplifieris capable of delivering 15.4 W of peak power into a4-Ω load while sustaining 11.6 W continuously with less than 0.03 % THD+N at a battery voltage of 12.6V.
Integrated speaker voltage and current senseprovides for real time monitoring of loudspeakerbehavior. A battery tracking peak voltage limiter withbrown out prevention optimizes amplifier headroomover the entire charge cycle of 2S or 3S batterysystems.Up to eight devices can share a common bus viaeither I2S/TDM + I2C.
The TAS2770 device is available in a 26-pin, 0.4-mmpitch QFN for a compact PCB footprint.

TAS2770主要特性:
1• High-Performance Mono Class-D Amplifier
– 20-W at 1% THD+N (4 Ω, 16 V)
– 15.4-W at 1 % THD+N (4 Ω, 12.6 V)
– 9.1-W at 1 % THD+N (8 Ω, 12.6 V)
– 8.2-W at 1 % THD+N (4 Ω, 8.4 V)
– 4-W at 1 % THD+N (8 Ω, 8.4 V)
• 0.03 % THD+N at 1 W (4 Ω, VBAT = 12.6 V)
• 32-μVrms A-Weighted Idle Channel noise
• 90-dB PSRR with 200 mVPP Ripple at 20 - 20 kHz
• 82.5% Efficiency at 1 W (4 Ω, VBAT = 12.6 V)
• < 1 μA HW Shutdown VBAT Current
• 42 mW/63 mW Idle Dissipation (8.4 V/12.6 V)
• Speaker Voltage and Current Sense
• Real-Time Diagnostics Using I/V Speaker Sense
– Over Current
– Short Circuit(short to power, short to groundand terminal-to-terminal short)
– Over-Temperature
• VBAT Tracking Peak Voltage Limiter with BrownOut Prevention
• 44.1-kHz to 192-kHz Sample Rates
• Flexible User Interfaces
– I2S/TDM: 8 Channels (32-bit / 96 kHz)
– I2C: 8 selectable Addresses
• MCLK Free Operation
• Low Pop and Click
• Power Supplies
– VBAT: 4.5 V to 16 V
– AVDD: 1.8 V
• Spread-Spectrum Low EMI Mode
• Thermal and Over Current Protection

TAS2770应用:
• Laptop Computers
• Bluetooth Speakers
• Home Automation
• Smart Speakers/IoT

图1.TAS2770功能框图

图2.TAS2770典型应用电路图

图3.立体声EVM元件布局图

PC立体声音频参考设计TIDA-01572
This stereo audio subsystem produces higher qualityaudio over CODEC driver solutions in PC applicationsusing the TAS2770 device. This device
enables theuse of a Smart Amp algorithm, which provides speakerprotection while maximizing the sound pressure level(SPL) by monitoring the physical conditions of thespeaker in real time. This design provides a workinglayout and design recommendations to enable a quickadaptation of this solution.
This stereo audio subsystem uses two TAS2770 devices for improved audio capabilities over CODECsolutions. The TAS2770 is highly configurable to various audio input formats and has integrated speakervoltage and current sensing, which can be used to determine the maximum audio signal whilesimultaneously protecting against thermal and mechanical failure mechanisms.
This design incorporates a simple power solution to provide the necessary rails to operate and interfacewith the TAS2770 device. The user is only required to provide VBAT with a supply ranging from 4.5 V to16 V.
For ease of use, this design incorporates an XMOS device, which allows for testing and developmentusing a USB interface. If desired, however, the board can be set to accept external I2C and I2S busconnections to test using another system, such as an audio analyzer.
After connecting the device to a PC running PurePath™ Console 3 with the TAS2770-specific application,the user can quickly and easily configure the device. Among the many features of the TAS2770 is abattery protection output limiter. This limiter controls the automatic gain control to help maintain a qualityaudio output while preventing excessive demand on the battery system. Brownout protection is alsoincluded to protect the system from failing due to potential demands generated by the audio system. Inaddition, the designer can configure the inter-chip limiter alignment (ICLA) to ensure that, while in amultichannel configuration, all the channels that are actively grouped together attack equally to maintainaudio cont
inuity and balance.

参考设计TIDA-01572主要特性:
• High-Performance Class-D Amplifier SupportsWide VBAT Supply Range of 4.5 V to 16 V
• 15-W Continuous Power Into 4 Ω at 12.6 V(1% THD+N)
• Integrated Voltage and Current Sense forDiagnostics
• 32-μV Idle Channel Noise and Spread SpectrumLow-EMI Mode
• Supports I2S and SoundWire™ Inputs
• Small 26-Pin QFN (3.5 mm × 4 mm)
• Input Multiplexing Supporting Multiple InputSources
参考设计TIDA-01572应用:
• PC and Notebooks
• Wireless (BT) Speaker
• Thermostat
• Video Doorbell
• Video Communications System

图4.参考设计TIDA-01572外形图

图5.参考设计TIDA-01572框图

图6.参考设计TIDA-01572电路图(1)

图7.参考设计TIDA-01572电路图(2)

图8.参考设计TIDA-01572电路图(3)

图9.参考设计TIDA-01572电路图(4)

图10.参考设计TIDA-01572电路图(5)

图11.参考设计TIDA-01572电路图(6)

图12.参考设计TIDA-01572电路图(7)
参考设计TIDA-01572材料清单:


图13.参考设计TIDA-01572 PCB设计图(1):顶层丝印

图14.参考设计TIDA-01572 PCB设计图(2):顶层焊接模

图15.参考设计TIDA-01572 PCB设计图(3):顶层铜

图16.参考设计TIDA-01572 PCB设计图(4):铜层2

图17.参考设计TIDA-01572 PCB设计图(5):铜层3

图18.参考设计TIDA-01572 PCB设计图(6):底层铜

图19.参考设计TIDA-01572 PCB设计图(7):底层焊接模

图20.参考设计TIDA-01572 PCB设计图(8):底层丝印

 
 
 
    您可能对以下产品感兴趣  
产品型号 功能介绍 兼容型号 封装形式 工作电压 备注
ACM3129 2×57W, 1% THD+N, 24V, 4Ω, BTL ; 1×110W, 1% THD+N, 24V, 2Ω, PBTL TSSOP-28(散热片在背部,支持外接散热器) 4.5V-26.4V 2×57W/110W高性能D类音频功放,超低功耗、展频功能、动态调整升压Class H
ACM3108 2×25W, 1% THD+N, 16V, 4Ω, BTL ; 1×50W, 1% THD+N, 16V, 2Ω, PBTL AD52068/TPA3110 TSSOP-28 4.5V-16V 动态调整升压CLASS H功能、25W双声道/50W单声道D类音频功放IC
ACM3128 2×32.5W, 1% THD+N, 24V, 8 , BTL; 1×65W, 1% THD+N, 24V, 4 , PBTL; 2×42W, 1% THD+N, 24V, 6 , BTL; 1×84W, 1% THD+N, 24V, 3 , PBTL; 2X48W, 1% THD+N, 22V, 4 , BTL; AD52090/TPA3110 TSSOP-28 4.5V-26.4V 动态调整升压CLASS H功能、40W立体声/80W单声道D类音频功放IC
ACM8615 21W, 单声道输出(8Ω, 20V, THD+N = 1%) 26W, 单声道输出 (8Ω, 20V, THD+N = 10%) QFN-16 4.5V-21V 内置DSP、I2S数字输入20W单声道D类音频功放IC
ACM8625P 2×33W, 立体声输出(6Ω, 21V, THD+N = 1%) 51W, 单声道输出 (8Ω, 21V, THD+N = 1%)  ACM8622/ACM8625M/ACM8628 TSSOP-28 4.5V-21V I2S数字输入33W立体声D类音频功放芯片、内置DSP小音量低频增强等算法
ACM8622 2×14W, 立体声输出(4Ω, 12V, THD+N = 1%); 2×10.5W, 立体声输出 (6Ω, 12V, THD+N = 1%) TAS5805/ACM8625/ACM8628 TSSOP-28 4.5V-14.5V 内置DSP音效处理算法、2×14W立体声/ 1×23W单声道、数字输入D类音频功放IC
ACM8625 2×26W, 立体声输出(8Ω, 22V, THD+N = 1%) 2×32W, 立体声输出 (8Ω, 22V, THD+N = 10%) TAS5805/ACM8628/ACM8622 TSSOP-28 4.5V-26.4V I2S数字输入26W立体声D类音频功放芯片、内置DSP小音量低频增强等算法
ACM8628 2×41W、立体声 (6Ω, 24V, THD+N = 1%) ; 2×33W, 立体声 (4Ω, 18V, THD+N = 1%) ; 1×82W, 单通道 (3Ω, 24V, THD+N = 1%) TAS5805/ACM8625/ACM8622 TSSOP-28 4.5V-26.4V 2×41W立体声 /1×82W单通道数字输入功放、内置DSP小音量低频增强等算法
HT560 2X40W/18V/4Ω或75W/24V/4Ω QFN-36 4.5V-26V 30W立体声D类I2S输入音频功放
HT7178 输入电压范围:2.7V -14 V;输出电压范围:4.5V-20V ;可编程峰值电流: 14A TPS61088/HT7167 DFN-20 2.7V-14V 20V 14A带输出关断的全集成同步升压IC
 
 
    相关产品  
 
 
·蓝牙音箱的音频功放/升压/充电管
·单节锂电内置升压音频功放IC选型
·HT7179 12V升24V内置
·5V USB输入、三节锂电升压型
·网络主播声卡专用耳机放大IC-H
 
M12269 HT366 ACM8629 HT338 

业务洽谈:手机:13713728695(微信同号)   QQ:3003207580  EMAIL:panbo@szczkjgs.com   联系人:潘波

地址:深圳市宝安西乡航城大道航城创新创业园A5栋307/309

版权所有:深圳市永阜康科技有限公司  备案号:粤ICP备17113496号