当前位置:首页->技术分享 |
|
BD99954应用处理器锂电池充电管理方案 |
|
|
文章来源:永阜康科技 更新时间:2017/12/18 11:21:00 |
在线咨询: |
|
rohm公司的BD99954是1到4节锂电池双模式充电管理器,小型5.0x5.0mm QFN封装和2.6x3.0mm芯片级CSP封装,提供双源电池充电器,两个端口BC1.2检测和用于电压,电流,温度的电池监视器以及告警控制器.主要用在空间严格限制的设备如小尺寸笔记本电脑,平板电脑和其它应用.本文介绍了BD99954主要特性,功能框图,应用电路以及评估板BD99954MWV EVK主要特性,电路图,USB-I2C电路图,材料清单和PCB设计图.
The Industry ’s First Dual-Mode Battery Charge ICBD99954 is a Battery Management LSI for 1-4 cellLithium-Ion secondary battery, and available in a 40pin0.40 mm pitch 5.0 mm x 5.0 mm QFN package and small41-ball 0.4mm pitch 2.6mm x 3.0mm Wafer-Level CSP package which is designed to meet high degree demandsfor space-constraint equipment such as Low profileNotebook PC, Tablets and other applications.
BD99954 provides a Dual-source Battery Charger, twoport BC1.2 detection and a Battery Monitor with severalalarm(INT#, PROCHOT#) outputsBD99954 is a Battery Manager IC for 1-4Cell Lithium-Ion / Lithium-Ion polymer secondary battery pack used in portableequipment such as Tablets, Ultra books or others.
BD99954 includes a Battery Charger, two port BC1.2 detection, a Battery Monitor for voltage, current, temperature andalarm(INT#, PROCHOT#) Controller.
BD99954主要特性:
Dual-source Battery Charger
High efficiency Step-Up/Down switching charger for1-4 cell Li-Ion/Li-poly battery
Two separate input sources for USB-VBUS and DCadapter.
Two port BC1.2 detectors.
JEITA compliant charging profile
Programmable parameters for Preconditioning, Prechargecurrent,and Fast-charge current
Programmable charging voltage
Programmable charge current
Programmable Switching Frequency: 600kHz to1.2MHz
Support USB BCS 1.2, ACA, ID pin, OTG
USB-VBUS Over Voltage Protection
Over Voltage Battery Protection
Battery Short Circuit Detection
Power Path Management with charge pump gatedriver
Flexibility power path control
Reverse Buck/Boost Option for USB/USB-PD
Bias voltage output for the external thermistor
PMON output
PROCHOT# output
Support Inhibit / Autonomous Charging
Battery Learn Function
Input Operating Range: 3.8V to 25V
Voltage Measurement for Thermistor.
Bias voltage output for the external thermistor.
SMBus Interface (Clock up friendly I2C) for Hostcommunication
Embedded OTPROM for initial settings
BD99954应用:
Ultrabook
Notebook PC
Ultra-mobile PC
Tablet PC

图1.BD99954功能框图

图2.BD99954应用电路图
评估板BD99954MWV EVK
This application note provides information on the BD99954MWV EVK board, which includes the bill of materials, schematics, boardlayout, and application data. In addition to this, a user manual for the I2C control software is included to help program theBD99954MWV.
The BD99954MWV EVK acts as a platform for the BD99954 battery management LSI. With the included software GUI, users canaccess the battery charging profile and modify and read back the registers of the BD99954.
评估板BD99954MWV EVK应用:
1-4 Li-ion Cells (in series) Battery Charging
评估板BD99954MWV EVK主要特性:
Reverse Buck/Boost Option
On-Board USB-to-I2C Communication Circuit
Input Operating Range: 3.8V to 25V
评估板BD99954MWV EVK工作极限和最大值:


图3.评估板BD99954MWV EVK外形图

图4. 评估板BD99954MWV EVK电路图(1)

图5. 评估板BD99954MWV EVK电路图(2):USB-I2C
评估板BD99954MWV EVK材料清单:


USB-I2C材料清单:


图6. 评估板BD99954MWV EVK PCB布局图(1):顶层

图7. 评估板BD99954MWV EVK PCB设计图(2): GND内层1

图7. 评估板BD99954MWV EVK PCB设计图(2):PWR内层2

图8. 评估板BD99954MWV EVK PCB设计图(3):底层
|
|
|
|
|
|
|
|
 |
您可能对以下产品感兴趣 |
 |
|
 |
产品型号 |
功能介绍 |
兼容型号 |
封装形式 |
工作电压 |
备注 |
HT317 |
2X42W/18V/4Ω或75W/24V/4Ω |
|
TSSOP-28 |
5V-26V |
42W立体声/75W单声道D类功放IC,,工作电压5-26V,极限耐压32V! |
FP8207 |
FP8207 是一款開關模式的電池充電控制器,輸入電壓應用範圍為4.6V~18V,可對單節或是多節鋰離子電池(最多三節)進行定電流或是恒壓充電,其最大充電電流為3A, |
|
TSSOP-14 |
4.6V-18V |
3A开关降压单节/双节/三节锂电充电管理IC |
FP6296 |
工作電壓範圍2.7V~12V;可調輸出電壓最高13V;内置10A的MOS |
|
ESOP-8 |
2.7V-12V |
内置MOS的10A大电流DC-DC异步升压IC |
FP5208 |
FP5208是非同步升壓控制IC,透過EXT Pin 控制外部NMOS,輸入低啟動電
壓2.5V 與寬工作電壓4.5V~24V |
|
SOP-8/DFN-12 |
4.5V-24V |
非同步升压控制IC,,最高升压可至42V提供5A的电流输出 |
CS5080 |
CS5080E是一款5V输入,支持双节锂电池串联应用,锂离子电池的升压充电管理IC.CS5080E集成功率MOS,采用异步开关架构,使其在应用时仅需极少的外围器件,可有效减少整体方案尺寸,降低BOM成本。CS5080E的升压开关充电转换器的工作频率为600KHz最大2A输入充电,转换效率为90%。 |
|
ESOP-8 |
3.44V-7.0V |
5V USB输入、双节锂电池串联应用、升压充电管理IC |
ANT2801 |
ANT2801 是一款宽范围电压输入,专门为双节锂电池充电的芯片,无需传统的5V适配器。 |
|
TSSOP-20 |
3V-6V |
5V USB 输入两节锂电池高效充电管理IC |
|
|
|
|
|
|