| 当前位置：首页->方案设计 |
|
| NXP NTBMS电池管理系统安全参考设计 |
|
|
| 文章来源：永阜康科技 更新时间：2019/9/6 10:13:00 |
在线咨询： |
| |
nxp公司的NTBMS电池管理系统,适用于汽车电池管理系统,用作锂电池的起动电池或辅助电池. NTBMS平台设计具有高度可靠性和安全性,和ISO 26262 ASIL C兼容.锂电池管理系统包括电池监测,电流测量,无源电池平衡,电池断路器控制,电池参数提取(充电状态,健康状态)的计算单元以及通过CAN和其它ECU通信.平台集成了高达ASIL C的系统诊断,过流保护,过充电保护,超温保护,过压保护,欠压保护(短路),非预期继电器关闭保护,非预期继电器开路保护和碰撞检测输入.主要用在汽车BMS锂电池起动电池,汽车辅助电池BMS,智能电网以及其它电池管理系统(医疗,电动自行车,轻型运输和工业).本文介绍了NTBMS主要特性,技术数据,框图和系统框图,系统连接框图与电路图.
NTBMS is a Battery Management System for manufacturer ofautomotive Battery Systems, used as Starter Battery or AuxiliaryBattery with Li-Ion cells.
The NTBMS platform is designed for systems with high demandon reliability and safety in compliance with ISO 26262 ASIL C.
NTBMS is a generic safety reference design for BMS developedin cooperation with NXP. The Battery Management System of Li-Ion battery includes cell monitoring, current sensing, passive cellbalancing, battery breaker control, computation unit for Batteryparameter extraction (such as State of Charge, State of Health)and communication to other ECU through CAN.
Battery management systems (BMS) are responsible to steerand control high-voltage batteries of Electric and Hybrid ElectricVehicles. This control unit is essential since several battery cellsare unified to a cluster to enhance battery capacity. It is a chargeregulator which should guarantee a stringent power supply ofthe engine.
BMS are essential to monitor state of charge, load distribution,temperature of each battery cell as well as of the whole batterypackage and development of the charging capacity.
NTBMS主要特性:
_ Integrated system diagnostic functions up to ASIL C
_ Overcurrent protection
_ Overcharge protection
_ Over-temperature protection
_ Over-voltage protection
_ Under-voltage protection (short circuit)
_ Protection against unintended relay close
_ Protection against unintended relay open
_ Crash detection input
NTBMS用户优势:
_ Accelerate time to market
_ Reduction in costs for development and certification
_ Safety Development Platform for BMS
_ Reference Design in compliance to ISO 26262 ASIL C
NTBMS典型应用:
_ Automotive BMS for Starter Battery with Li-Ion battery
_ Automotive BMS for Auxiliary Battery
_ Smart Grids
_ Other Battery Management opportunities (medical, e-Bike,light transportation, industrial)
图1.NTBMS基板和NT SafeSOMmicro外形图
NTBMS基板主要技术数据:
电源
The device is designed for operation with 12V to 18V DC powerSupply. Operation with other supply voltages is not permitted.The supply voltage is connected via the connection cable providedfor this purpose.
环境条件
温度
The device is designed for storage and operations at the followingtemperature ranges:
_ Storage temperature: -15℃ to +70℃
_ Operating temperature: 0℃ to +40℃
电池特性
电流载流能力
_ 250 A permanent;
_ 600 A for 40 s;
_ 1400 A for 1 s
电池管理系统电流
_ operating current < 25 mA@RT
其它特性
_ Intrusive diagnostics (performed by MCU)
_ Memory storage (RAM& flash)
_ Power management (low power and normal mode)
_ LIN for starter batteries
_ CAN for the auxiliary batteries.
图2.NTBMS系统框图
The application is a Battery Management System (BMS) evaluation platform for a 14V Li-Ion battery (including cell monitoring, current sensing, passive cell balancing, battery breaker control, computation unit for Battery parameter extraction and communication to other ECU through CAN.
The NT BMS consists of a general purpose Safety System on Module (NT SafeSOMmicro) which is an ASIL C ready microcontroller platform, including two microcontrollers which are supervising each other and an ASIL D qualified System Basis Chip providing all necessary voltages, CAN PHY and Watchdog functionality.
Second part is the NT BMS Baseboard where all battery management specific components are located. The three main components are:
Battery Cell Controller
Current measurement shunt resistor
Breaker control circuit
图3.NTBMS框图
图4.NTBMS系统连接框图
图5.NTBMS电路图(1)
图6.NTBMS电路图(2)
图7.NTBMS电路图(3)
图8.NTBMS电路图(4)
图9.NTBMS电路图(5) |
| |
|
|
|
|
|
| |
| |
| |
 |
您可能对以下产品感兴趣 |
 |
|
 |
| 产品型号 |
功能介绍 |
兼容型号 |
封装形式 |
工作电压 |
备注 |
| VAS5118 |
VAS5118 是一颗多节串联锂电池组监控芯片，通过I2C通信接口与主控制器配合，形成电池管理系统(BMS)。 |
|
TSSOP-24 |
0.3V-40V |
3节至28节串联电池监控芯片 |
| VAS5176 |
VAS5176 是一款8.5V-24V 输入,高度集成的开关型锂离子/聚合物电池充电管理芯片, 以高精度调节2A充电电流,和电池电压。 |
VAS5175A/VAS5176 |
ESOP-8 |
8.5V-24V |
8.5V-24V输入2A开关降压型2节/3节4节锂电池充电管理IC |
| VAS5175H |
VAS5175H 是一款5V-24V 输入,开关降压型1节4.35V/2节8.7V锂离子/聚合物电池充电芯片, 以高精度调节2A 充电电流,和电池电压。它密切监测电池组的温度只在设置安全温度范围下允许充电,还提供电池检测、预充电调节、充电饱充和充电状态指示等功能。 |
VAS5175A/VAS5176 |
ESOP-8 |
5V-26V |
2A开关降压型1节4.35V/2节8.7V锂电池充电管理IC |
| VAS5175A |
VAS5175A 是一款5V-24V输入,高度集成的开关型锂离子/聚合物电池充电芯片, 以高精度调节2A充电电流,和电池电压。它密切监测电池组的温度只在设置安全温度范围下允许充电,还提供电池检测、预充电调节、充电饱充和充电状态指示等功能。 |
VAS5175H/VAS5176 |
ESOP-8 |
5V-24V |
2.0A, 1/2节锂电池开关型充电器 |
|
| |
|
| |
|
|
